IC HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Mazushakar Morr
Country: Egypt
Language: English (Spanish)
Genre: Business
Published (Last): 8 November 2012
Pages: 160
PDF File Size: 3.5 Mb
ePub File Size: 10.61 Mb
ISBN: 477-1-80599-612-7
Downloads: 91542
Price: Free* [*Free Regsitration Required]
Uploader: Malakree

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. Skip to main content. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. They are paired with 2 12 series of encoders. What is Web Browser. If you want security you can connect any of the 8 pins to 5V to make it high.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. The IC has a built in oscillator. This pin will go high when a data is received. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

  DOCMD.SENDOBJECT ACSENDREPORT PDF

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

This pin powers the IC should use only 5V. If any valid data is received they can be obtained iic these four pins. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. This high-density System-in-Package SiP integrates controller, power switches, and support components.

In the above circuit I hr12d set the 8-bit address data as 0b, by connecting all address pins to ground. Valid transmission; active high.

This oscillator can be used by connecting these two pins through a 1M Resistor 17 H12d Transmission VT This pin will go high when a data is received. TL — Programmable Reference Voltage. HT12D is capable of decoding 12 ht12dd, of which 8 are address bits and 4 are data bits. In simple terms, HT12D converts the serial input into parallel outputs. A valid transmission in indicated by a high signal at VT pin.

Choosing Battery for Robots. These are the 8-bit address bits, which is used to protect your data.

Supply voltage; 5V 2. It is mainly provided to interface RF iic infrared circuits. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. So out jt12d the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. These two ICs together form an Encoder and Decoder pair.

  C1WEBREPORT EXPORT TO PDF

The input data code is decoded when no error or unmatched codes are found.

How IC HT12D works?

Arduino based GPS receiver. It is not mandatory to use it. It is very important that your Decoder should have the same address of that of the encoder. They can also be connected to LED to physically view the received data.

HT12D Decoder IC

Choosing Motor For Robots. Connected to the Ground of circuit. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Interface SD Card with Arduino.

Interface GPS with Arduino. A basic circuit diagram for the HT12D IC is shown below I the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

The data on 4 bit latch type output pins remain unchanged until new is received. SPI Module of Arduino. Submitted by admin on 27 October The serial input data is compared with the local addresses three times continuously.

This oscillator can be used by connecting these two pins through a 1M Resistor. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Virgin Galactic — Commercial Space Flight.